Vacuum‐driven fluid manipulation by a piezoelectric diaphragm micropump for microfluidic droplet generation with a rapid system response time

Recently, we developed a convenient microfluidic droplet generation device based on vacuum‐driven fluid manipulation with a piezoelectric diaphragm micropump. In the present study built on our previous work, we investigate the influence of settings applied to the piezoelectric pump, such as peak‐to‐peak drive voltage (V_p‐p) and wave frequency, on droplet generation characteristics. Stepwise adjustments to the drive voltage in ±10‐V_p‐p increments over the range of 200?250 V_p‐p during droplet creation revealed that the droplet generation rate could be reproducibly controlled at a specific drive voltage. The droplet generation rate switched within <0.5 s after the input of a new voltage. Although the droplet generation rate depended on the drive voltage, this setting had almost no influence on droplet size. The frequency over the selected range (50?60 Hz) did not markedly influence the droplet generation rate or droplet size. We show that the current fluid manipulation system can be conveniently used for both droplet generation and for rapid droplet reading, which is required in many microfluidic‐based applications.     

X-ray radiography of aluminum cathodes eroded in high-current vacuum arcs

The aim of the study presented in this paper was to characterize quantitatively the erosion of aluminum cathodes in high-current vacuum arcs. The experimental setup comprised two current generators. The first one, capable of generating a current of amplitude up to 350 kA, was used to produce a plasma jet, that is, the object to be investigated. The second generator was used to produce a source of probe radiation for imaging the object under investigation in soft x rays of energy ?ν ≈ 0.5–3 keV. The findings of the study are based on experimental data obtained by electrophysical and radiographic methods. It has been shown that the cathode erosion rate in a high-current vacuum arc is a function of the charge passed through the cathode.     

Zero dissipation limit to rarefaction wave with vacuum for the one-dimensional non-isentropic micropolar equations

The zero dissipation limit of the one-dimensional non-isentropic micropolar equations is studied in this paper. If the given rarefaction wave which connects to vacuum at one side, a sequence of solution to the micropolar equations can be constructed which converge to the above rarefaction wave with vacuum as the viscosity and the heat conduction coefficient tend to zero. Moreover, the uniform convergence rate is obtained. The key point in our analysis is how to control the degeneracies in the vacuum region in the zero dissipation limit process.     

含气率对PTS时压力容器内流动与传热的影响

本文对反应堆压力容器紧急安注时的流动与传热特性在1/10的模型上进行了流动可视化、局部传热系数以及混合函数的试验研究。针对三个热冲击敏感区域的部分测点,比较了环腔流速为0.5m/s、安注流速为1～30 m/s时不同含气率对下降环腔内流动与传热特性的影响,得出并分析了不同测点传热系数、混合函数的变化规律。研究结果表明:随着含气率增大,安注流体与环腔流体的混合增强;下降环腔内的含气率对小安注流速时的流动与传热影响显著,而对大安注流速时影响较小。     

数字散斑相关方法及其在碳纤维复合材料压力容器变形测量中的应用

提出了一种新的基于图像灰度梯度迭代的数字散斑相关方法(DSCM,digital speckle correlation method)。通过使用DSCM测量碳纤维复合材料压力容器在水压下的局部区域的位移场和应变场,分析了复合材料压力容器的轴向和环向的变形特征,为碳纤维复合材料压力容器的优化设计提供了理论和实验依据。     

Microwave promoted energy-efficient N-formylation with aqueous formic acid

Microwave-induced organic reaction enhancement (‘MORE’) chemistry technique (open vessel; controlled microwave energy to stay below the boiling point of the reaction mixture) was used for the N-formylation of aliphatic and aromatic amines and amino heterocycles with aq formic acid (80%) on a multiple gram scale in a few minutes.     

BEPCⅡ大功率波导真空阀门的研制

 大功率波导真空阀门是BEPCⅡ直线加速器微波系统的重点改进项目，作为微波大功率传输和真空密封双重功能的超高真空微波器件，机械结构比较复杂，制造工艺难度大。经过各方努力，已经研究完成16台大功率波导真空阀门，并在2004年全部安装在加速器上使用。目前进入到波导真空阀门的脉冲功率为30~50 MW，高功率运行工作状态良好。对阀门从设计原理、机械结构、微波测试及高功率运行等方面作了较详细的阐述。     

Development of Vacuum Monitoring System in the HL-2A tokamak

HL-2A is the first divertor tokamak in China. The vacuum system is one of the important parts of the HL-2A tokamak, which has to be work well during the physics campaign in 2004. As the tokamak machine is separated from the operation staff during discharges, to guarantee the safe and reliable operation of the vacuum system, it is necessary to watch the vacuum system outside the machine hall with an automatic monitoring system. The paper describes the design and manufacture of the monitoring system.     

Equilibrium Shapes of Pressure Vessel Domes in Asymmetric Winding

Errors in the programs of winding pressure vessels can lead to an asymmetric reinforcement structure, which affects the equilibrium shape of their domes and the tension in the left and right families of filaments. In this paper, equations determining the equilibrium shape of the domes, the tension in filaments, and the shear stresses between layers are obtained. Examples with winding trajectories in the form of geodesics and constant-deviation lines are considered. It is found that, for pressure vessels, in the absence of external torque, the tension levels in filaments of the left and right families differ considerably. It is also revealed that, for actual friction coefficients in winding, the shear stresses taken up by the binder are insignificant. __________ Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 6, pp. 743–752, November–December, 2005.